5/8″ PET Strapping – 1250 lb Break

green pet strap-opalus
pet strap-opalus
pet strap roll
green pet strap-opalus
pet strap-opalus
pet strap roll
  • Width: 5/8 in nominal
  • Material: Polyester (PET)
  • Break class: 1250 lb nominal target
  • Thickness: Factory value pending
  • Coil length: Factory value pending
  • Color / core / finish: Approved sample required

5/8 x 1250 lb break pet strapping is intended for established 5/8-inch packing lines where a tested 950 lb coil leaves too little strength margin. Rather than immediately specifying 1400 lb, the intermediate grade can be compared on the same load, with the same band count and machine settings. Its 1250 lb rating applies to unjoined PET strap, not allowable working tension or pallet weight. Welded-joint performance, tension remaining after load settlement and usable footage per coil help determine whether changing grades is worthwhile.

Qualifying 1250 lb PET on an Existing Line

Evaluate this nominal 1250 lb grade on the intended 5/8-inch equipment. Confirm the actual dimensions, finish and winding, then distinguish strap rupture from joint slip, corner damage or load movement during the trial. Other widths and finishes are listed in the polyester strapping range. If a corrected joining process resolves the failure, separately reassess the 950 lb grade before changing material.

Benefits

  • Intermediate rating: Trial 1250 lb before specifying 1400 lb.
  • Coil yield: Compare finished packs, including waste and rework.
  • Tooling: Trial the candidate roll on existing 5/8-inch equipment.
  • Failure diagnosis: Identify breaks, faulty joints or load movement.

What Should Be Verified Before Switching an Existing Line to 1250 lb PET Strapping?

Equal width does not guarantee a drop-in replacement. Compare gauge, width tolerance, core, coil diameter, finish and camber. At line speed, record misfeeds per 100 cycles, weld defects and tension settings. Joint efficiency = welded-joint breaking force / unjoined breaking force x 100%, using one lot. Keep the strap count, protected corners and load condition unchanged.

Applications

  • Masonry pallets: Investigate 950 lb strap rupture with protected corners.
  • Lumber bundles: Observe restraint after the stack settles.
  • Rigid components: Review band routing across uneven edges.
  • Pallet lines: Compare coils on existing 5/8-inch equipment.

Technical Data Sheet – 1250 lb Qualification

Property1250 lb product statusAcceptance evidence
PolymerPETApproved resin grade
Nominal width5/8 inLot width / tolerance
Nominal break class1250 lbf targetStraight-pull lot result / method
ThicknessFactory value pendingMeasured gauge in / min / max
Usable coil lengthFactory value pendingMeasured ft per coil
Core ID / face widthFactory value pendingMeasured dimensions in
Color / finishApproved sample pendingActual supplied grade
Elongation at breakNo SKU result suppliedGauge length / test speed / %
Retained tensionNo SKU result suppliedStarting force / elapsed h / C / %
Weld-joint efficiencyNo SKU result suppliedTool / settings / joint break / %
Camber / straightnessNo SKU result suppliedLateral deviation mm / test span
Machine feedingNo SKU trial suppliedLine speed / feed count / faults

1250 lbf is a target class, not a factory result. Release requires an approved drawing and lot report.

Confirming Usable Footage for the Qualified Coil

Use the confirmed coil length rather than a strength-class assumption. Published external 1250 lb examples include a 0.035 in gauge and 4200 ft coil; these are not AOBERIS TAPE roll specifications. Compare accepted strap cuts after setup waste, incomplete welds and roll-end losses. Record the approved core, winding and usable footage for repeat orders.

Repeat Supply Must Match the Qualified Coil

Keep the approved coil, drawing and settings, including dimension limits, finish and winding. For later lots, record measured dimensions, strap and joint breaking forces, elongation and camber. Review changes in resin or welding against this baseline. A 24 h retained-tension comparison at fixed force, temperature and load geometry is a proposed test, not an existing result. ASTM D3950-23 is a technical reference, not proof of compliance.

Acceptance Criteria for 1250 lb PET Strapping

Approve this grade through documented feeding, joint-strength and load-restraint checks on the intended equipment and package. Keep strap count and protected corners consistent during trials. More unjoined strength will not correct a slipping weld or an unstable load. For a different strength class, evaluate 1400 lb PET strapping under its own joint and feeding settings.

FAQ

Does the 1250 lb rating establish finished-joint strength?

No. The joint must be tested with the selected surface and joining tool.

Is 0.035 in the confirmed supplied gauge?

No. It is an external 1250 lb example; the actual SKU gauge needs approval.

How should roll yield be compared?

Use accepted strap cuts after waste, incomplete welds and roll-end losses.

What makes a repeat lot comparable to the trial?

An approved sample, dimensional limits, lot tensile data and recorded joining conditions.

Scroll to Top

Get A Free Quote Now !

Contact Form Demo (#3)