5/8″ Extruded Polyester Strapping – 750 lb Break

pet strap manufacturer
pet strap roll
green pet strap-opalus
pet strap manufacturer
pet strap roll
green pet strap-opalus
  • Width: 5/8 in / 15.875 mm
  • Material: Extruded, oriented PET
  • Reference thickness: 0.020 in / 0.508 mm
  • Nominal break grade: 750 lbf / 3.34 kN
  • Reference finish: Smooth / black
  • Reference core options: 16 x 3 / 16 x 6 in

At 5/8 inch wide, this 750 lb extruded polyester strapping serves stable cartons and regular bundles that need contact width without a heavier break grade. Published equivalents use 0.020-inch (0.508 mm) oriented PET, with 5,700 ft and 2,850 ft coil formats in supplier ranges. The choice depends on whether the load remains secure at this strength, the joint survives handling and the selected reel fits the dispenser. Actual thickness, finish, coil format and measured performance must be confirmed for AOBERIS TAPE supply. The 2,850 ft option is a shorter industrial reel, not a 300 ft field coil. For intermittent work away from a fixed dispenser, the 300 ft PET short-coil format shows a much smaller roll-length alternative. Compare gauge, declared footage, and holder dimensions before substituting products.

Benefits

  • Broad contact: The band is 25% wider than 1/2-inch strap; protect vulnerable corners.
  • Thin section: Nominal area is 8.06 mm2, 20% below same-width 0.025-inch stock.
  • Two coil formats: 5700 ft versus 2850 ft in published ranges; confirm supply.
  • Tool fit: The 0.508 mm reference thickness approaches some heads’ minimum gauge.

How Does Coil Length Affect Output with 750 lb PET Strapping?

At 20 ft per completed band, 5,700 ft permits 285 theoretical bands versus 142 from 2,850 ft. Overlap, threading waste and coil ends reduce actual yield; machine cycle time stays unchanged. Published configurations use 16 x 6 and 16 x 3 in cores, respectively. The wider face may not fit the current dispenser. Check reel outside diameter, permitted roll mass and payout direction before substituting the longer format.

What to Check from the Outer Layers to the Core

Near the core, a long roll may feed differently if curvature or winding pressure varies. Sample the outer, middle and inner windings of the nominal 0.020-inch band. Log width, minimum and maximum thickness, and camber over a fixed gauge length. If tracking changes, record coil position and reel alignment before altering tool settings. This is an inspection method, not measured AOBERIS TAPE performance.

Technical Data Sheet (TDS)

ParameterReference data / valueEvidence status
Material / structureExtruded oriented PETPublished comparator
Nominal width5/8 in / 15.875 mm750 lb reference grade
Nominal thickness0.020 in / 0.508 mm750 lb reference grade
Nominal break force750 lbf / 3.34 kNUnjoined strap rating
Nominal section area8.06 mm2Calculated / width x thickness
Reference finish / colorSmooth / blackSupplier-specific
Long coil length5700 ft / 1737.36 mPublished option / verify
Long coil core16 x 6 inPublished option / verify
Short coil length2850 ft / 868.68 mPublished alternative
Short coil core16 x 3 inPublished alternative
Long-reel outside diameterMeasured mm not yet suppliedConfirm dispenser clearance
Elongation at breakMeasured % unavailableLot test required
Retained tensionMeasured % after defined h unavailableRecord initial tension
Joint efficiencyMeasured % unavailableSpecify tool / weld settings
Width / thickness toleranceMeasured min-max mm unavailableLot inspection required
Camber / straightnessDeviation in mm unavailableState gauge length

These are published comparison specifications, not AOBERIS TAPE batch data. For other widths or surfaces, see the polyester strapping range. Confirm this SKU’s actual gauge, coil configuration and test record.

Applications

  • Supported carton pallets: Run bands across flat faces; protect vulnerable corners.
  • Rigid multipacks: Check load movement and joints after vibration.
  • Uniform bundles: Use a tested strap pattern; guard exposed edges.
  • Established strapping stations: Qualify thin-gauge feeding and the longer reel.

The Thin-Gauge Limit on an Automatic Head

One friction-weld head specifies 8-19 mm widths and 0.50-1.00 mm thickness. The reference 15.875 x 0.508 mm band sits only 0.008 mm above the head’s lower thickness limit. Check measured minimum gauge, particularly near the core, then observe feeding and seal consistency during a trial. The head’s 3500 N maximum tension exceeds the nominal 3336 N unjoined strap break force; never treat that equipment limit as a safe operating setting. Test completed joints with the intended tooling. For a broader material overview, review extruded polyester strapping selection, then qualify the actual strap, joint and tool combination for the intended load.

Which Shipment Conditions Make a Wide, Lower-Break PET Strap Practical?

Use this wide 750 lb grade where handling trials confirm adequate restraint. If a band breaks, locate the failure at the edge, strap body or weld before increasing strength. When the straight strap itself is limiting, trial the 5/8-inch 950 lb PET strapping grade with identical band count and corner protection. Its nominal unjoined break force is approximately 27% higher, but that does not determine allowable pallet weight.

FAQ

Is 0.020 inch a guaranteed minimum thickness?

No. It is nominal reference data; request lot tolerances and measured minima.

Will a 16 x 6 in coil fit an existing dispenser?

Check face width, outside diameter, roll mass, core and payout direction.

Can 5/8-inch strap run through a 1/2-inch feed head?

Only if guides, strap path and weld head accept the wider band.

Does 750 lb describe the finished joint?

No. It is unjoined nominal strength; verify joint force with production tooling.

Scroll to Top

Get A Free Quote Now !

Contact Form Demo (#3)